Follow Along on My Build.
Get The truth about Magnets 4 Energy.
Do Not get Fooled

The buying Process Goes Real well.
First they take you to A Page that offers you some other related subjects.
I did not want any of them so I just clicked in the middle of the page where it says “No, thanks I would like to pass up this amazing offer“. Then fill in The credit card info. Click Bank is real Reputable so no need to worry about your info.

There are 5 Different Free Bonuses That You Do Get.

1 Run your car on water,
2 The Renewable Energy Handbook,
3 Living Green,
4 Gas Saving Devices,
5 Fuel Efficient Vehicles,

Check Back Often For my next report.

The first half of Magnets 4 Energy gives You some basics of solar setups
And identifies some of the components. The second half is well written
Without a lot of fluff I like it when they get to the point.
I have printed off the parts list and off to the hard ware store.
Back from the hard ware store and What A disappointing trip not a single Idem was found. Let my fingers do the walking and made some calls and was able to find some of the stuff but was not willing to do all the running. So I have decided to buy Most of the components on line and share where I found them and there cost. I have also converted the metric hardware to SAE Just easier in my area. (List at bottom)

Check Back Often For my next report.

The price of the parts are proving to be much more expensive then the $100.00 that the Magnets 4 Energy system suggest. If Someone out There finds them cheaper  please let me know so I can  pass it on.
The Molds are a pain a good saber saw worked good for cutting them out.
I have access to A metal lathe to finish them. It took a lot of sanding and many coats of varnish to get them smooth. I used shellac and that was not the best because I had some wrinkling in the mold from the heat.

Hi Sorry for not getting to this sooner I have been very busy.

I just followed the Plans for the Coils and it worked out fine.

The Magnets worked out ok on the steel plates as the plains show but I will put some mat in the next set as there was some cracking in the fiberglass nothing serious but I did not like it.

The spine with the spindle needed a cross piece for ease of fastening it down. But the rest worked out fine By the plains.

The finished product seem well built but it Does not run under its own power it does put out good power when turned by some other source.
I have hooked it up to a wind turbine but having trouble getting sufficient speed to put out sufficient power.

Fiberglass Supplies (Murray’s Oreilly 37.99)
Fiberglass Mat 1 oz sq foot – 1 sq Yard (Murray’s Oreilly 5.99)
Talcum power Filler (Drug Store 5.49)

Magnets (16) .787 x 1.969 x 1.969
www.magnet4sale.com

Ceramic Magnets C8 2″X2″X1″ Hard Ferrite Magnets     16     $1.60 ech        $25.60

Stainless Steel Wire  .079 (Harbor Freight)

Enameled Winding Wire 14AWG .067
Magnet4Less

Braded Wire 14AWG 20’ (Tractor Supply)
Bridge Rectifiers (2) 25A  200V Single Phase
Heat sink (Tractor Supply)
Steel for spine 15” x 1” x 2” x .125” (Tractor Supply)
Steel Plate For Disk Must be magnetic ¼” x 12 1/8” Diameter

Threaded Rod 3/8”-16 x 36” (Tractor Supply)
32 – 3/8-16 hex nuts (Tractor Supply)
16 – 3/8 Washers (Tractor Supply)
Threaded Rod 5/16”-18 x 16” Most places you will have to by 36” pieces (Tractor Supply)

8 – 5/16-18 nuts (Tractor Supply)

2 – 3/16 x ¾ Machine screw with nuts (Tractor Supply)

Hub With bearings
www.trailerpart.com
Part #
SKU:                        Product          Quantity           Price
T0R104BT8X        T0R104BT8X        1                $6.95       Spindle
LOBT121E             LOBT121E            1                $16.95     Hub Ass 4 on 4”

Metric to Inch
6 MM = .236
13 MM = .512
15 MM  = .591
20 MM  = .787
30 MM = .512
40 MM = 1.575
45 MM = 1.662
50 MM = 1.969
60 MM = 2.363
75 MM = 2.953
100 MM = 3.938
125 MM = 5.922
130 MM = 5.119
140 MM = 5.515
178 MM = 7.009
199 MM = 7.836
250 MM = 9.844
305 MM = 12.009
320 MM = 12.006
355 MM = 13,978
315 MM = 12.403
325 MM = 12.797
340 MM = 13.388
360 MM = 14.175
368 MM = 14.490
380 MM = 14.963
500 MM = 19.688

Using the Magnets 4 Energy, you will be able to generate absolutely free electric energy. It is easy to construct and doesn’t require any external source of energy to power itself. The Magnets 4 Energy works by itself, and can independently power your home and help you say goodbye to the power bill.